|
|
|
|
|
|
|
|
|
|
|
|
|
|
Delco main shaft standard shim +/- 0.030-0.032" thick. Generally all cast iron body Delco distributors will use 2 pieces. May fit others
|
Wico XB coil core
|
6791 Wico XB distributor main shaft bushing. 2 used, priced and sold each.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Autolite/Prestolite advance weight
|
Delco rotor fits most cast iron distributors replaces 1905590 and 820445 delco #'s. ABC520 DR158
|
Ford front mount distributor gasket set
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Delco distributor advance spring . Replaces 1911070 , 1912765 , Sold as a pair / set . We have not yet complied a list of distributor numbers these fit. Does fit 1111558
|
Delco distributor advance spring . Replaces 1883899 Sold as a pair / set . We have not yet complied a list of distributor numbers these fit. Does fit 1111418 1111411
|
Ford distributor primary copper conductor for side mount distributors -> 1964
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Farmall distributor clip bracket
|
International Farmall distributor advance spring set
|
Ford side mount distributor rotor clip
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Substitute for 90-2067 Prestolite distributor primary wire connector insulator and clip used on 7-136 IBT series and others
|
Delco distributor advance spring . Substitute for 1904292. Sold as a pair / set . We have not yet complied a list of distributor numbers these are suitable for but they will work on the Delco distributors with a screw type cap used on John Deere 3010 3020 4010 4020
|
Prestolite distributor bushing fits most IBT IDU and some other distributors. Approximately 1/2" ID X 5/8" OD X 1" long. May require reaming to fit shaft after installation. Most distributors require 2 . These are straight solid wall bushings. If your original bushings has a hole, groove or any other special machining, this will need to be done at installation. Generally oiler hole is drilled after installation , any grooves or similar would need to be made prior to installation.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
New eccentric adjusting point screw for most cast iron Delco distributors After installing in your old plate, backside must be flared/coined/expanded to retain it in place. A center punch or flat punch with the head(slotted side) resting on a flat surface generally works fine . Head is roughly 9/32" diameter and 1/8" diameter where it passes through plate.
|
Prestolite distributor plate IBT
|
Ford side mount distributor cap clip
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Delco Remy distributor terminal round hole
|
NEW Delco distributor terminal
|
Ford distributor primary screw and insulator kit. Conductor from this part to your point set is MFDS281. This fits ford tractors with side mount distributors up to 1964 like 8N(will not fit front mount), Jubilee, NAA 600 700 800 900 2000 and 4000 series. Will not work on post 1964 3 cylinder tractors. Replaces 34079S 350032S 44713S 7RA12233 7RA12234
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Delco Remy distributor clip and bracket
|
Delco Remy distributor clip and bracket
|
Delco Remy centrifugal advance weight
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Farmall horizontal distributor cap clip
|
replaces 353915R91 international advance weight for distributor
|
replaces 352277R11 international weight guard for distributor
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Farmall distributor main shaft bushing. Fits IH horizontally mounted tractor distributors used on A, B, C, H , M Supers, ETC. . May require reaming to fit shaft after installation.
|
Delco Remy 2 7/8" Main Shaft bushing
|
Delco Remy 2" Main Shaft bushing Standard Size
|
|
|
