|
|
|
|
|
|
|
|
|
|
|
|
|
|
#12 split lock washer
|
8-32 X 5/16 " Fillister head slotted screw . Common use is throttle plate screws on single barrel DLTX carburetors, they also fit our new Ensign throttle shafts and have other uses. Order lockwasher separately, part 8LW
|
#4 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#4 X 1/4" SEMS Pan head slotted screw with internal tooth lock washer
|
#6 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
10-24 X 5/8" Fillister head slotted screw . Common use is Farmall cub bowl to body screws and some other carburetors. Order lockwasher separately, part 10LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4". Order lockwasher separately, part 12LW
|
8-32 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
#8 X 5/16" SEMS Pan head slotted screw with external tooth lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Carburetor mounting gasket 2-3/8" center to center mounting. Typically used on small flange medium bowl Marvel Schebler TSX carbs like TSX 464, International H Farmall , Zenith 267 series size 8, etc. 24520D
|
carburetor flange mounting gasket oblong mounting holes will fit most 2 1/4 , 2 5/16 and 2 3/8 center to center with 1/4" or 5/16" mounting bolts
|
Zenith 61 and 161 body gasket
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
carburetor flange mounting gasket will fit 1 13/16 " center to center mounting holes for 1/4" bolts and a 15/16" - 1" center hole used with IH cub 251235R1 some Wisconsin's and anything else with these measurements
|
Carburetor mounting gasket 2-11/16" center to center mounting. Typically used on majority of medium bowl Marvel Schebler TSX carbs , Holley updrafts used on Ford tractors , most Zenith size 10 carbs without vacuum orifice in flange face, etc.
|
Zenith 67 series carburetor body gasket
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
carburetor flange mounting gasket . Mounting bolt centers are 3-5/16" . 2" center hole w/slots for vacuum pickup . size 7 (1 15/16" bore +/- ) Zenith carburetors are a common application
|
carburetor flange mounting gasket . Mounting bolt centers are 3-9/16" . 2 3/16 " center hole w/slots for vacuum pickup . size 8 ( 2 3/16" bore +/- ) Zenith carburetors are a common application
|
carburetor flange mounting gasket for Zenith 69 series and Marvel Schebler USX carburetors . Mounting bolt centers are 3-5/16" . 2" center hole
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Packing gland for small size Zenith load adjustment assemblies(3/8" threads in carb body) . Will not work with female nut type on Zenith carbs only male packing nuts . Will fit all Marvel Schebler that use 5/16 male packing nuts. Can also be used in place of 44-51T packing. #'s to be added later as it is an extensive list. For other size/style packings please email.
|
Zenith carburetor threaded plug fits most Zenith carbs that use 3/8-24 gasketed plug
|
Zenith load needle packing used in multiple applications. This generally fits all zenith load adjusters with male packing nuts and carburetor casting threads of 1/2" thread such as 63 sizes 12 14 16 , 62 size 12 , 69 series, etc. Also fits most 68 228 267 series when a female packing nut is present and dimensions are similar. Packing rough(not exact) dimensions are 3/8" outside diameter, 3/16" inside diameter and thickness. If your carb has a small male packing nut see 44-51 variations(packing OD is roughly 9/32")
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zenith TU TU4C carburetor intake mounting commonly used on John Deere and Caterpillar pony starting motor replaces JD F2115R Caterpillar 4B6977
|
Zenith 62 and 162 carburetor bowl to body gasket size 9 and 10
|
carburetor flange mounting stud assembly 1/4 diameter 1-1/4" overall length coarse threads for carb , fine thread for manifold side includes lock washer and nut sold each . 2 typically used on updraft carburetor
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zenith 62 and 162 carburetor bowl to body gasket size 12
|
Interchangeable with original style leather packing 44-51L . This is a higher quality long lasting teflon packing gland for adjusting needle on most Zenith assemblies that thread in carb 3/8" and have a male thread packing nut and most Marvel Schebler carburetors (that use packing glands) and possibly others. #'s to be added later as it is an extensive list.
|
Knurled brass throttle bushing for 5/16" shaft. Presses into 3/8" hole. 1/2" in length. May need to be shortened depending on the application. C9-56
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
Knurled brass throttle bushing for 1/4" shaft. Presses into 5/16" hole. 1/2" in length. May need to be shortened depending on the application.
|
Zenith TU load needle housing gasket. This gasket goes between the bowl lid and the right angle load needle housing, we've mainly seen this on Caterpillar applications.
|
|
|
