|
|
|
|
|
|
|
|
|
|
|
|
|
|
#12 split lock washer
|
8-32 X 5/16 " Fillister head slotted screw . Common use is throttle plate screws on single barrel DLTX carburetors, they also fit our new Ensign throttle shafts and have other uses. Order lockwasher separately, part 8LW
|
#4 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#4 X 1/4" SEMS Pan head slotted screw with internal tooth lock washer
|
#6 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
10-24 X 5/8" Fillister head slotted screw . Common use is Farmall cub bowl to body screws and some other carburetors. Order lockwasher separately, part 10LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4". Order lockwasher separately, part 12LW
|
carburetor flange mounting gasket oblong mounting holes will fit most 2 1/4 , 2 5/16 and 2 3/8 center to center with 1/4" or 5/16" mounting bolts
|
carburetor flange mounting gasket will fit 1 13/16 " center to center mounting holes for 1/4" bolts and a 15/16" - 1" center hole used with IH cub 251235R1 some Wisconsin's and anything else with these measurements
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
carburetor flange mounting stud assembly 1/4 diameter 1-1/4" overall length coarse threads for carb , fine thread for manifold side includes lock washer and nut sold each . 2 typically used on updraft carburetor
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
porous bronze carburetor drip hole plug 1/8 NPT . This threaded fitting can be used on any carburetor with 1/8" NPT threads for the throat drip hole
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
porous bronze carburetor drip hole plug 1/4 NPT . This threaded fitting can be used on any carburetor with 1/4" NPT threads for the throat drip hole
|
carburetor flange mounting stud assembly 3/8 diameter 1-1/2" overall length coarse threads for carb , fine thread for manifold side includes lock washer and nut sold each . 2 typically used on updraft carburetor
|
fuel strainer screen to repair most IH fuel fittings such as H M Supers, 300 460 etc. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.312" outside diameter
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A quantity of one is 100 pieces ordered. 12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4".
|
Drain cock
|
1/8" NPT Drain cock with internal seal, highly recommend this for the DLTX 3 and is a great replacement on the International Farmall carburetors if you don't want to pay for OEM style. This valve handle actually screws away, instead of toward the carb, so it works well in some particular applications.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
fuel strainer screen to repair most IH fuel fittings such as H M Supers, 300 460 etc. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.312" outside diameter
|
1/4" NPT Drain cock with internal seal, highly recommend this for the Zenith K5. This valve handle actually screws away, instead of toward the carb, so it works well in some particular applications.
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel connector strainer JD L/M/40/320/330/420/430
|
|
|
