|
|
|
|
|
|
|
|
|
|
|
|
|
|
#12 split lock washer
|
8-32 X 5/16 " Fillister head slotted screw . Common use is throttle plate screws on single barrel DLTX carburetors, they also fit our new Ensign throttle shafts and have other uses. Order lockwasher separately, part 8LW
|
#4 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#4 X 1/4" SEMS Pan head slotted screw with internal tooth lock washer
|
#6 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
10-24 X 5/8" Fillister head slotted screw . Common use is Farmall cub bowl to body screws and some other carburetors. Order lockwasher separately, part 10LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4". Order lockwasher separately, part 12LW
|
carburetor flange mounting gasket oblong mounting holes will fit most 2 1/4 , 2 5/16 and 2 3/8 center to center with 1/4" or 5/16" mounting bolts
|
carburetor flange mounting gasket will fit 1 13/16 " center to center mounting holes for 1/4" bolts and a 15/16" - 1" center hole used with IH cub 251235R1 some Wisconsin's and anything else with these measurements
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
carburetor flange mounting stud assembly 1/4 diameter 1-1/4" overall length coarse threads for carb , fine thread for manifold side includes lock washer and nut sold each . 2 typically used on updraft carburetor
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
Brass 7/16" hex head 1/8 NPT plug
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
carburetor flange mounting stud assembly 3/8 diameter 1-1/2" overall length coarse threads for carb , fine thread for manifold side includes lock washer and nut sold each . 2 typically used on updraft carburetor
|
fuel strainer screen to repair most IH fuel fittings such as H M Supers, 300 460 etc. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.312" outside diameter
|
Fuel connector strainer ford ferguson
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Farmall cub float valve ( needle & seat ) fits IH carbs not zenith. New design eliminates needle sticking closed and allows full flow with less movement keeping bowl at a more constant level. Does not fit Zenith carbs replaces 31-500. Also fits Carter UT with cast iron throttle body. Will not fit Carter UT aluminum throttle body.
|
A quantity of one is 100 pieces ordered. 12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4".
|
Drain cock
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/8" NPT Drain cock with internal seal, highly recommend this for the DLTX 3 and is a great replacement on the International Farmall carburetors if you don't want to pay for OEM style. This valve handle actually screws away, instead of toward the carb, so it works well in some particular applications.
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
fuel strainer screen to repair most IH fuel fittings such as H M Supers, 300 460 etc. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.312" outside diameter
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4" NPT Drain cock with internal seal, highly recommend this for the Zenith K5. This valve handle actually screws away, instead of toward the carb, so it works well in some particular applications.
|
Carburetor Kit
fits most Carter model N carburetors that we're aware of, including but not limited to Replaces OEM:
CLINTON: 220-701
CLINTON: 231-555
CLINTON: 275-776
CLINTON: 275-778
CLINTON: 39-268-500
CLINTON: 39-887-500
CLINTON: 39-914-500
FOLEY/PLP: 116-150
GRAVELY: 010792
GRAVELY: 010923
GRAVELY: 017341
GRAVELY: 20050700
KOHLER: 220701
KOHLER: 231555
KOHLER: 25 757 01
KOHLER: 25 757 01-S
KOHLER: 275776
KOHLER: 275778
Fits Models: CLINTON D, VS700, 800, A, VS800, 900-1000, 900-2000,1000, D1100, 1200-2000 and VS2100, with Carter carburetors
GRAVELY K91-K301, K321 and K482
KOHLER K91 thru K301, K321, K482 and M8 thru M12
Specs: •Not compatible with greater than 10% ethanol fuel
|
Carter UT carburetor kit. Fits carbs with aluminum top and bottom.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel connector strainer JD L/M/40/320/330/420/430
|
IH basic carter carb kit
|
Carburetor float 21-121S carter
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fits Carter # UT923S, UT2621S, UT2701S, UT2702S, UT2703S, UT2705S, UT2706S and other carburetors with aluminum throttle body. Replaces Carter # 21-164S
|
Fuel strainer elbow fitting For 5/16" inverted flare lines, male nut behind flared tubing fits into this female fitting. 1/8" NPT male for carburetor connection. Replaces AT14778 fits some John Deere International and others
|
IH basic carter carb kit
|
|
|
