|
|
|
|
|
|
|
|
|
|
|
|
|
|
10-24 X 5/8" Fillister head slotted screw . Common use is Farmall cub bowl to body screws and some other carburetors. Order lockwasher separately, part 10LW
|
Carburetor mounting gasket 2-11/16" center to center mounting. Typically used on majority of medium bowl Marvel Schebler TSX carbs , Holley updrafts used on Ford tractors , most Zenith size 10 carbs without vacuum orifice in flange face, etc.
|
IH/Farmall idle screw spring
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Carburetor mounting gasket for IH 1 1/4 and 1 3/8 carbs and some others. 2 11/16" mounting centers
|
International Farmall Cub carburetor float pin replaces 251299R1
|
Carburetor mounting gasket 2-3/8" center to center mounting. Typically used on small flange medium bowl Marvel Schebler TSX carbs like TSX 464, International H Farmall , Zenith 267 series size 8, etc. 24520D
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Carburetor float pin fits Zenith carburetors using float pin numbers C120-3 C120-6 C120-53 and IH M size carbs 1-1/4 and 1-3/8 SAE .
|
International Farmall carburetor bowl gasket fits Super H , M , most number series 1 1/4 & 1 3/8" carburetors replaces 47388DA
|
carburetor flange mounting gasket will fit 1 13/16 " center to center mounting holes for 1/4" bolts and a 15/16" - 1" center hole used with IH cub 251235R1 some Wisconsin's and anything else with these measurements
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Farmall carburetor governor connection gasket . Replaces 66727D . This gasket goes between carburetor and governor tube on IH Farmall H through the 50 series carbs. H , M , W series , hundred (300 400 etc) and fifty (350 450 etc) series. All with the enclosed governor tube connection.
|
International Farmall Cub carburetor throat drain pierced plug only . Part of 354263R91 assembly 64907D 57957D 27445DB
|
International Farmall H carburetor throttle shaft bushing replaces 45109DA T818 . For 1/4" shaft. Presses into 3/8" hole. 1/2" long. May have to be shortened in some applications other than Farmall H.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Farmall M type carburetor throttle shaft bushing for end opposite of governor linkage replaces 47390D Also fits both sides of number series with IH made 1-1/4 1-3/8 carbs and exposed throttle lever. Also fits Zenith K5 linkage side throttle bushing on some carbs like F20 IH etc replacing CR9-16
|
IH Farmall gas starting, diesel F-8 carburetor manifold gasket
|
IH Farmall gas starting, diesel F-8 carburetor bowl gasket
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Farmall carburetor choke shaft friction spring replaces 46059D
|
Knurled brass throttle bushing for 5/16" shaft. Presses into 3/8" hole. 1/2" in length. May need to be shortened depending on the application. C9-56
|
International Farmall Cub carburetor idle needle replaces 351958R1
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
Knurled brass throttle bushing for 1/4" shaft. Presses into 5/16" hole. 1/2" in length. May need to be shortened depending on the application.
|
International Farmall Cub carburetor bowl gasket replaces 251337R3
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Brass 7/16" hex head 1/8 NPT plug
|
Load needle packing used on practically all IH made carbs from H and up Replaces 24703DA
|
porous bronze carburetor drip hole plug 1/8 NPT . This threaded fitting can be used on any carburetor with 1/8" NPT threads for the throat drip hole
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
international farmall load needle packing nut
|
fuel strainer screen to repair most IH fuel fittings such as H M Supers, 300 460 etc. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.312" outside diameter
|
International Farmall Cub carburetor choke friction spring replaces 351845R11
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Manifold and bowl gasket for International F8 diesel starting carburetor. For International / Farmall Fits: [ ID6, ID9, MD, MDV, ODS6, Super MD, Super MDV, Super MDV-TA, Super MTA, Super WD6, Super WD6TA, Super WD9, Super WDR9, TD14, TD14A, TD6, TD6-61, TD9, UD14, UD6, UD6A, UD9, W400, W450, WD6, WD9, WDR9, 400, 450, 600, 650 (DIESEL WITH F8 STARTING CARB) ]; Replaces:
32606DD and 53459DA IHS997
|
porous bronze carburetor drip hole plug 1/4 NPT . This threaded fitting can be used on any carburetor with 1/4" NPT threads for the throat drip hole
|
International Farmall Cub carburetor main jet 0.031" orifice size replaces 354192R91
|
|
|
