|
|
|
|
|
|
|
|
|
|
|
|
|
|
#12 split lock washer
|
8-32 X 5/16 " Fillister head slotted screw . Common use is throttle plate screws on single barrel DLTX carburetors, they also fit our new Ensign throttle shafts and have other uses. Order lockwasher separately, part 8LW
|
#4 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#4 X 1/4" SEMS Pan head slotted screw with internal tooth lock washer
|
#6 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
10-24 X 5/8" Fillister head slotted screw . Common use is Farmall cub bowl to body screws and some other carburetors. Order lockwasher separately, part 10LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Marvel Schebler TSX choke friction washer. This washer along with a spring and shoulder screw (24-480 and 15-397) holds friction on the choke lever on carburetors designed as such. Some applications are "L" John Deere hand choke, some Allis Chalmers carburetors, some International Farmall carburetors , some TSV carburetors and others. wasCarburetor number will hopefully be added at a later date when we have time.
|
12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4". Order lockwasher separately, part 12LW
|
8-32 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#8 X 5/16" SEMS Pan head slotted screw with external tooth lock washer
|
80-169 brass cup plug nominal 1/4" diameter for some Marvel Schebler TSX throttle shaft hole and DLTX 67 71 72 73 drilling plug on throttle body and choke shaft
|
80-160 brass cup plug nominal 1/8" diameter used on DLTX 67 71 72 73 and some other carburetors
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
80-167 brass cup plug nominal 3/16" diameter for some Marvel Schebler TSX choke shaft hole and DLTX 67 71 72 73 drilling plug on throttle body
|
Marvel Schebler carburetor idle speed screw spring used on all TSX , USX , 2 barrel DLTX and single barrel carb numbers DLTX 67 71 72 73 107U 108U
|
Carburetor mounting gasket 2-3/8" center to center mounting. Typically used on small flange medium bowl Marvel Schebler TSX carbs like TSX 464, International H Farmall , Zenith 267 series size 8, etc. 24520D
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
carburetor flange mounting gasket will fit 1 13/16 " center to center mounting holes for 1/4" bolts and a 15/16" - 1" center hole used with IH cub 251235R1 some Wisconsin's and anything else with these measurements
|
Carburetor mounting gasket 2-11/16" center to center mounting. Typically used on majority of medium bowl Marvel Schebler TSX carbs , Holley updrafts used on Ford tractors , most Zenith size 10 carbs without vacuum orifice in flange face, etc.
|
Manifold gasket
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DLTX single barell carburetor choke end mounting gasket can be substituted for 321R
|
Packing gland for small size Zenith load adjustment assemblies(3/8" threads in carb body) . Will not work with female nut type on Zenith carbs only male packing nuts . Will fit all Marvel Schebler that use 5/16 male packing nuts. Can also be used in place of 44-51T packing. #'s to be added later as it is an extensive list. For other size/style packings please email.
|
Idle adjusting needle fits most TSX up to 1 5/16" throttle bore
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4-28 Drill plug used on Marvel Schebler DLTX TSX and TTX carbs
|
Interchangeable with original style leather packing 44-51L . This is a higher quality long lasting teflon packing gland for adjusting needle on most Zenith assemblies that thread in carb 3/8" and have a male thread packing nut and most Marvel Schebler carburetors (that use packing glands) and possibly others. #'s to be added later as it is an extensive list.
|
Knurled brass throttle bushing for 5/16" shaft. Presses into 3/8" hole. 1/2" in length. May need to be shortened depending on the application. C9-56
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
Knurled brass throttle bushing for 1/4" shaft. Presses into 5/16" hole. 1/2" in length. May need to be shortened depending on the application.
|
5 PACK - Holley 1970 updraft float (Ford 3 cylinder tractor 2000-3000-4000 etc) assist spring. This is basically a vibration dampening spring. Float pin passes through and spring exerts a slight upward force on float. Unknown what carburetor numbers used this spring at this time. Also Walbro 98-89-7
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
porous bronze carburetor drip hole plug 1/8 NPT . This threaded fitting can be used on any carburetor with 1/8" NPT threads for the throat drip hole
|
porous bronze carburetor drip hole plug 1/4 NPT . This threaded fitting can be used on any carburetor with 1/4" NPT threads for the throat drip hole
|
Brass 7/16" hex head 1/8 NPT plug
|
|
|
