|
|
|
|
|
|
|
|
|
|
|
|
|
|
#12 split lock washer
|
8-32 X 5/16 " Fillister head slotted screw . Common use is throttle plate screws on single barrel DLTX carburetors, they also fit our new Ensign throttle shafts and have other uses. Order lockwasher separately, part 8LW
|
#4 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#4 X 1/4" SEMS Pan head slotted screw with internal tooth lock washer
|
#6 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
10-24 X 5/8" Fillister head slotted screw . Common use is Farmall cub bowl to body screws and some other carburetors. Order lockwasher separately, part 10LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4". Order lockwasher separately, part 12LW
|
8-32 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
#8 X 5/16" SEMS Pan head slotted screw with external tooth lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Marvel Schebler VH choke position/friction spring fits VH 12 14 53 61 63 92 93 and possibly others
|
Marvel Schebler carburetor idle speed screw spring used on all TSX , USX , 2 barrel DLTX and single barrel carb numbers DLTX 67 71 72 73 107U 108U
|
carburetor flange mounting gasket will fit 1 13/16 " center to center mounting holes for 1/4" bolts and a 15/16" - 1" center hole used with IH cub 251235R1 some Wisconsin's and anything else with these measurements
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Packing gland for small size Zenith load adjustment assemblies(3/8" threads in carb body) . Will not work with female nut type on Zenith carbs only male packing nuts . Will fit all Marvel Schebler that use 5/16 male packing nuts. Can also be used in place of 44-51T packing. #'s to be added later as it is an extensive list. For other size/style packings please email.
|
Idle adjusting needle fits most TSX up to 1 5/16" throttle bore
|
Gasket set for marvel schebler TCX
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4-28 Drill plug used on Marvel Schebler DLTX TSX and TTX carbs
|
Interchangeable with original style leather packing 44-51L . This is a higher quality long lasting teflon packing gland for adjusting needle on most Zenith assemblies that thread in carb 3/8" and have a male thread packing nut and most Marvel Schebler carburetors (that use packing glands) and possibly others. #'s to be added later as it is an extensive list.
|
Knurled brass throttle bushing for 5/16" shaft. Presses into 3/8" hole. 1/2" in length. May need to be shortened depending on the application. C9-56
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
Knurled brass throttle bushing for 1/4" shaft. Presses into 5/16" hole. 1/2" in length. May need to be shortened depending on the application.
|
porous bronze carburetor drip hole plug 1/8 NPT . This threaded fitting can be used on any carburetor with 1/8" NPT threads for the throat drip hole
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
porous bronze carburetor drip hole plug 1/4 NPT . This threaded fitting can be used on any carburetor with 1/4" NPT threads for the throat drip hole
|
Brass 7/16" hex head 1/8 NPT plug
|
Marvel Schebler TSV carburetor body to bowl gasket. This gasket goes between the main throttle body and bowl castings.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Choke return spring
|
fuel strainer screen to repair most IH fuel fittings such as H M Supers, 300 460 etc. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.312" outside diameter
|
24-A141 Marvel Schebler SL2 air valve spring. originally came in AR732R carburetor kit
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Load Jet for marvel schebler DLTX 85 , 98 and TSX 654 715 732 845 917 946 974 975 and TSXU 837 , 838 and VH 44 , 71
|
Load or main Jet for marvel schebler TSX 680 880
|
Porous bronze press fit throat drain fits some TSX and small zenith carbs. Roughly 0.366"(3/8") in diameter and 0.177"(not quite 3/16") thick. For a thinner element see C135-29.
|
|
|
